미니미 영문메뉴얼중에 push-it 관련해 독해가 안되고 이써요
페이지 정보
본문
소프트리미트와 마찬가지로 컴프레서 기능을 하는건데요
the main differences between the two compression surves (제생각엔 curves 인데 오타로 s 로 쓰인거 같음) are the attack and release times. These parameters are adaptive and adjust according to the charcterisics of the signal.
쉽게 말해서, 이게 PUSH-IT 회로는 일반 컴프레서에 달린 어택과 릴리스타임이 입력되는소스에따라 자동으로 변환되는 오토모드 상태라는 이야기 인가요?
관련자료
승남님의 댓글
두 컴프레션 특성의 가장 큰 차이는 어택과 릴리스 타임입니다. 이 파라메터들은 시그널의 특성에 따라 (적응되어,) 조정되어집니다.
-------------------------------------------
어색하지만..^^;; 위의 내용을 머 대충 직역하자면 이런식이네요.(아,surve는 측량, 개관따위의 뉘앙스로 쓰이는 의미입니다. 나름대로 해석하시면 될 것 같습니다.)
말씀하신 것처럼, 입력시그널에 따라서 어택타임과 릴리스타임이 변하는 회로인 것 같군요.
-------------------------------------------
어색하지만..^^;; 위의 내용을 머 대충 직역하자면 이런식이네요.(아,surve는 측량, 개관따위의 뉘앙스로 쓰이는 의미입니다. 나름대로 해석하시면 될 것 같습니다.)
말씀하신 것처럼, 입력시그널에 따라서 어택타임과 릴리스타임이 변하는 회로인 것 같군요.
전성국님의 댓글
앗 정말 감사합니다. 미니미 정말 좋은거 같네요 컴프도 내장되구 참고로 메뉴얼 원문입니다.
Push-IT is a unique gain control circuit consisting of a compressor and limiter that are integrated with Soft
Limit. All compressors and limiters adjust gain and are controlled by a detection circuit known as a sidechain.
Every sidechain has a certain response time, and as a result it is possible for occasional fast transients to evade
the limiting action. When used with Push-IT’s limiter, Soft Limit smoothes out any transients that may slip by the
limiter’s response time. You have the ability to chain this limiter with either of the two different Push-IT compression
circuits. When used, Push-IT provides significant extra “punch” and gives the user almost total security
from overloading the digital outputs.
The main differences between the two compression surves are the attack and release times. These parameters
are adaptive and adjust according to the characteristics of the signal. Compression curve number one has
much quicker attack and release times. This circuit will lend itself well to percussive instruments, acoustic guitars,
and sources with fast attack.
Compression curve number two has slower attack and release times. This circuit is better suited for bass guitar
and vocals, which tend to have slower transient peaks.
The graph below illustrates the various compression and limiting curves generated by the combination of
Soft Limit and Push-IT. Soft Limit is engaged by the three-position toggle switch in the upper center of the front
panel. This is labeled “OFF” to the left – neither Soft Limit (SL) nor Soft Limit + Compression (SLC) enabled;
“SL” for the center position – Soft Limit only; and “SLC” to the right – Soft Limit + Compression (SLC) enabled.
In the SLC position, the lower “Curve” switch is used to select curve 1, 2 or 3.
그다음 커브 1,2,3 의 그래프가 나옴(플럭인인 울트라펑크 컴프의 경우 knee 선택함에따라 변하는 그래프있죠 그런거가 나오네염)
Push-IT is a unique gain control circuit consisting of a compressor and limiter that are integrated with Soft
Limit. All compressors and limiters adjust gain and are controlled by a detection circuit known as a sidechain.
Every sidechain has a certain response time, and as a result it is possible for occasional fast transients to evade
the limiting action. When used with Push-IT’s limiter, Soft Limit smoothes out any transients that may slip by the
limiter’s response time. You have the ability to chain this limiter with either of the two different Push-IT compression
circuits. When used, Push-IT provides significant extra “punch” and gives the user almost total security
from overloading the digital outputs.
The main differences between the two compression surves are the attack and release times. These parameters
are adaptive and adjust according to the characteristics of the signal. Compression curve number one has
much quicker attack and release times. This circuit will lend itself well to percussive instruments, acoustic guitars,
and sources with fast attack.
Compression curve number two has slower attack and release times. This circuit is better suited for bass guitar
and vocals, which tend to have slower transient peaks.
The graph below illustrates the various compression and limiting curves generated by the combination of
Soft Limit and Push-IT. Soft Limit is engaged by the three-position toggle switch in the upper center of the front
panel. This is labeled “OFF” to the left – neither Soft Limit (SL) nor Soft Limit + Compression (SLC) enabled;
“SL” for the center position – Soft Limit only; and “SLC” to the right – Soft Limit + Compression (SLC) enabled.
In the SLC position, the lower “Curve” switch is used to select curve 1, 2 or 3.
그다음 커브 1,2,3 의 그래프가 나옴(플럭인인 울트라펑크 컴프의 경우 knee 선택함에따라 변하는 그래프있죠 그런거가 나오네염)
